JIS G3131 SPHC/ SPH D steel plate /sheet is stamping and cold forming steels ,SPHC,SPHD and SPHE are symbols used in the Japanese Industrial Standards for steel sheets.They are characterized by a minimum tensile strength of 270MPa.sp.info JIS G3131 Drawing Quality Hot Rolled SPHD Steelssp.info JIS G3131 Hot-roll mild steel plates, sheet and stripJIS G3131 Hot-roll mild steel plates, sheet and strip 1. Scope The Japanese Industrial Standard specifies the hot-rolled mild steel plates, sheets and strip (hereafter referred to as "steel sheet and coil")intended for general fabrication purposes and drawing. Remarks 1. The standards cited in this Standard are given in Attached Table 1. 2.sp.infocarbon steel jis G3131 mechanical strength
JIS G 3131 Hot-Rolled Mild Steel Sheets and Coils Examples of Standards — Chemical Compositions and Mechanical Properties Designation Chemical Composition (%) Tensile Test Bending Test Tensile Strength (N/mm2) Elongation (%) Test Piece Bending Angle Inner Diameter Thickness (mm) Test Piece 1.2 ≦t ＜1.6 1.6 t 2.0 Thickness (mm) 2.0 t＜2.5 ...sp.info Pickled and Oiled Steel CoilsJIS SAPH 310~440 products are specially designed for automobile structural use, tensile strength from 310 to 440 N/mm 2 , which can be used in automobile structural applications.sp.info JIS G3131 Hot-Rolled Steel - RGSClassification Spec Chemical Composition(%) Tensile Strength N/mm² Elongation (%) C Mn P S ≥1.20mm to <1.60mm ≥1.60mm to <2.00mm ≥2.00mm to <2.50mm ≥2.50mm to <3.20mm ≥3.20mm …sp.info Kobe Steel’sChemical components (%) Tensile testing Bending test P S Tensile strength (N/mm2) Yield point (N/mm2) Elongation (%) Test piece (JIS) Bending property Thickness (mm) Bending angle Inner radius Test piece Thinner than (JIS) 6 mm 6 mm or thicker and thinner than 8 mm 8 mm or thicker and 14 mm or thinner 1.6 or more, but less than 2.0 2.0 or more, but
SPHC,SPHD and SPHE are symbols used in the Japanese Industrial Standards for steel sheets.They are characterized by a minimum tensile strength of 270MPa.sp.info SPECIAL STEEL Company-Business:Steel plate shearing ...SPHC. JIS G3131. No special strength requirements of the product parts . General molding, bending, such as wire piping, bicycle parts and other gear sets. SPHD SPHE. JIS G3131. Low yield strength, high elongation rate, anti-ear extension. Complex formation or severe bending of steel pipes, multiple deep drawing for cup parts, motor housing ...sp.info :: Equivalent Standards :: A/SA516-70, A/SA515-70, ST52-3 ...ASME SA516 Grade 60/70 Plates, API 5L X52 Seamless Pipes, API 5L X60 Seamless Pipes, API 5L X65 Seamless Pipes, API 5L X70 Seamless Pipes, S355J2G3 EN10025 Plates, ST52-3 DIN17100 Plates, SA515 Grade 60/70 Plates, SA182 F11 Bars, SA182 F22 Bars, SA182 F91 Bars, SA182 F5 Bars, SA240 Grade 321H Plates, SA240 Grade 347H Plates, SA240 Grade 316L Plate, API5L X52 LSAW/DSAW …sp.info SPHE - BEBON steel - SPHE steel plateJIS G3131 SPHE steel plate /sheet is stamping and cold forming steels , SPHE is symbols used in the Japanese Industrial Standards for steel sheets.They are characterized by a minimum tensile strength of 270MPa. we also can supply SPV355,SPHC,SPHD,please contact us if you need
Jul 12, 2019 · JIS G3131 Grade SPHC commercial quality. When it is infeasible to allow the centre of the test piece to be at a quarter-width from a side edge, the sampling should be performed as close to the aforementioned position as possible. However the width of SPHC material ranges to mm. To minimize this effect, quality HR4 should be specified.Some results are removed in response to a notice of local law requirement. For more information, please see here.sp.infoJIS G3131 SPHD steel plate steel,JIS G3131 SPHD steel ...sp.info Flat Rolled ProductsJIS G3141-SPCC SD. Size Designation: Sheet: thickness (mm) x width (mm) x length (m) Coil: width (mm) x thickness (mm) Mechanical Propertiessp.info JIS G3131 Low carbon steel plate and steel strip,JIS G3131 ...
Specification :JIS G3141 Symbol of Quality Grades Surface Finish Symbol Application / User Remarks SPCC As-Annealed SPCC-A General Use Commercial Quality Standard Temper Grade Dull Finish SPCC-SD General Use,Furniture, Tubes, Cabinet, Drum, …Some results are removed in response to a notice of local law requirement. For more information, please see here.
You may also leave contact information, we will contact you as soon as possible!
Tel: 0086-371-8615 1827
E-Mail: [email protected]
Address: Development Zone, Zhengzhou, China